Seiko to show new RCE2560 printhead

Seiko Instruments is to launch a new printhead, the RCE2560, which is essentially a 600dpi version of the existing 360dpi RC1536 but with faster speeds for water-based inks that will allow Seiko to target new markets including packaging and textiles.

Ali Eranpurwala, head of inkjet printhead sales at Seiko Instruments Europe, explains: “We have taken the RC1536 printhead that we already have with full nozzle level recirculation, and we have reduced the size of the channels to pack in more nozzles to get 600 dpi. So each row, instead of having 90dpi now has 150dpi in the RCE2560. In total there are four nozzle rows, which combine to form 600dpi.”

The RCE2560 has a print width of 108.3mm with 2560 nozzles. The head can generate drop sizes from 9 to 30 picolitres with a jetting frequency of 40kHz. This should lead to a very competitive print speed of 100mpm at 600dpi. It has a jetting velocity of 7mps at a throw distance of 3mm. It can print both horizontally and vertically. In addition, where the RC1536 only supported a single channel, the new head has two channels meaning that two colours can be jetted at 300 dpi each.

The other big change is that Seiko has upgraded the electronics within the printhead, which has allowed it to introduce a new Isolated channel mode. Seiko started its printhead business through licensing Xaar’s shared wall shear mode technology, as did Konica Minolta and Toshiba Tec as well. The shared wall means that there is a single wall between adjacent ink chambers. Electrodes on either side of these walls allowed the walls to be flexed in either direction to force the ink out of the ink chamber and through the nozzle in a sheared mode. Previously, Seiko relied on the waveform to apply a positive charge to the electrodes to push the walls in one direction.

For those inks that do not conduct currents, such as oil-based or UV inks, it was possible to trigger the electrodes on the inside wall as well as the outer wall, which allowed the walls to be flexed in both directions. However, as Eranpurwala explains: “With water-based inks we could not apply any current on the inner electrodes because they would be conducting, only on the outer electrode.” This meant that the shared walls between the ink chambers could only be flexed in one direction, which limited the performance with aqueous inks.

Eranpurwala continues: “But the new electronics allow us to use new waveforms, still just on the outer side but we can do this in both a positive and negative way, flexing that wall in both directions.” 

The net result is that this head is much better suited to water-based inks than previous Seiko printheads. He adds: “This allows us to obtain high directional accuracy because we can transfer more energy to the drops, as we can go outwards and inwards with our piezos.”

Eranpurwala explains: “We come from the ceramics market where we get a lot of pressure from the industry to print from a further distance and to do that we need to transfer a lot of energy to the drops so that means that the movement of the piezo in both directions is necessary. When we moved to the water-based inks we lost that squeeze motion because we could not trigger the electrodes on the inside of the channels. Now we are regaining this capability by using the positive and negative pulse on the electrodes that are not in the channel of ink.”

OEMs are free to design their own waveforms but Eranpurwala notes: “It is open but we tell them that it is not an easy thing to do so if they allow us to do it then it is better. We don’t put a lock on it so people can change it if they want to but we can’t warranty the printhead after that as its difficult for us to know what they have done with the waveform. He adds: “Some of the ink manufacturers prefer to make their own waveform and they keep it to their ink so we do that with them.”

He says that Seiko has some experience in letting customers work their waveform having already opened it up for the RC1536 head, noting: “The RC1536 is much easier for waveform because there is no negative, we have only the positive movements but now that we have the positive and negative we ourselves don’t know how difficult it will be. So we don’t know how feasible it will be for anyone to change the waveform.”

Ali Eranpurwala, head of inkjet printheads for Seiko Instruments Europe.

Otherwise, the fundamental design remains the same, including the piezo and the electrode deposition process. Besides water-based inks, the RCE2560 will also jet UV-curable, oil and solvent-based inks. In addition, it will handle a very wide range of fluid viscosity, from 5 to 20cP, and possibly beyond this. Ryoichiro Yamashita, technical support manager for Seiko Instruments Europe, says that Seiko does not have any experience above 20cP so for now the range is listed as 5-20cP.

There is no heating or temperature control on the head. Yamashita says that its not needed, noting: “It’s difficult to handle heating the ink only on the printhead because we have a very high flow rate so it is better to control the temperature by the ink system.”

Eranpurwala says: “We have a good relationship with customers which is based on the technical support that we give them. Having that strong presence of technical staff here in Europe, and the nozzle level recirculation, the 600dpi and the through flow technology with this high viscosity range, all these things are quantifiable benefits but I think the core benefit is still the way we do business, which people now expect from us.”

Seiko has also worked with both Meteor Inkjet and the small German company Aewa who have both developed drive electronics to support the RCE2560.

Initially Seiko will focus on the corrugated market, though Ali Eranpurwala adds: “But textiles is also something that we are looking at.” He explains: “We are now approaching clients from all different markets, like packaging, and we have glass printing, even 3D printing and some people are asking us for direct to shape. So now we have to choose a few and start working with them because we can’t support everyone at the same time.”

The first samples of the new head should be available later this summer, around August, and Seiko will select some beta customers then. Eranpurwala adds: “We expect to go into full production by the end of this year.”

The RCE2560 print head will be shown at Drupa and you can find further details from seiko-instruments.de.


Posted

in

, , ,

by

Tags:

Syndicate content

You can license the articles from Printing and Manufacturing Journal to reproduce in other publications. I generally charge around £150 per article but I’m open to discussing this for each title, particularly for publishers that want to use multiple stories. I can provide high res versions of images for print publications.

I’m used to working with overseas publishers and am registered for VAT with the UK’s HMRC tax authority but obviously won’t charge VAT to companies outside the UK. You can find further details and a licensing form from this page, or just contact me directly here.

Support this site

If you find the stories here useful then please consider making a donation to help fund Printing and Manufacturing Journal, either as a one-off or a repeat payment. Journalism is only really useful if it’s truly independent and this is the only such news source serving the print/ manufacturing sectors.

However, there are costs involved in travelling to cover events, as well as maintaining this site, not to mention the time that it takes to carry out research, check facts and interview people. So if you value this work, then please help to maintain it and keep it free to read.

Subscribe

Never miss a story – subscribe to Printing and Manufacturing Journal to receive an email notification every time an article is published here. It’s completely free of charge and you can cancel the subscription at any point without any hassle. There’s no need to provide any information other than an email address and subscribers details are not for sale so there’s no risk of any further marketing spam.

Related stories

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *