Nano Dimension results reveal turmoil

Nano Dimension has announced its financial results for 2024, which show the scale of the challenge facing the current management after the turmoil of the previous few years. 

I think it’s fair to say that Nano Dimension has been through a fairly busy – some might say chaotic – period. To recap briefly, this started in 2022 when the company raised a substantial amount of cash to fund further acquisitions. That was followed by an offer from Murchinson, one of Nano Dimension’s largest shareholders, to acquire the company. The board at that time accused Murchinson of simply trying to take over the company’s cash reserves, and then started a very aggressive effort to spend all that cash by acquiring Stratasys. 

Not surprisingly, Stratasys turned down this offer, though Nano Dimension continued to make increasingly aggressive offers and to buy a lot of Stratasys’ stock throughout 2023. At the same time, Nano Dimension also acquired a number of other companies, including Additive Flow, Desktop Metal and Markforged. However, the shareholders eventually sided with Murchinson after a vote in December 2024, leading to a shake-up in the management team and a change in strategy. 

The 2024 annual report was itself delayed from its usual March date to the hard deadline of the end of April while the company completed its acquisition of Markforged. The results show that revenue for the year was up 3 percent over 2023 at $57.8 million but that’s where any good news stops. The total cost of revenues rose from $30.8 million in 2023 to $32.8 million in 2024 while the gross profit fell from $25.5 million to $25 million.

The gross margin fell by 43 percent. The operating result improved from a loss of $124.8 million to a mere loss of $86.4 million. Altogether the company recorded a net loss of $96.9 million, which was 74 percent worse than the $55.6 million loss of 2023. Nano Dimension attributes this worsening of the net loss to a revaluation of its investments in Stratasys shares. 

However, the company has begun a restructuring program in the fourth quarter and this has delivered some improvements. Thus the sales and marketing expenses fell slightly from $31.7 million to $29.9 million, while the general and admin expenses dropped from $58.2 million to $40 million. Other expenses improved from a loss of $1.6 million to a plus of $5.9 million. 

The entire senior management team has been replaced since December. On 8 April, the board appointed the then chairman, Ofir Baharav, as the company’s new Chief Executive Officer. The interim CEO, Julien Lederman, has now become the Chief Business Officer.

Robert Pons, who joined the board as a director in December 2024, who has now taken over as chairman, stated: “Mr. Baharav’s proven ability to drive strategic change and operational efficiency is precisely what Nano Dimension needs at this critical juncture.” Baharav has nearly three decades of experience in capital equipment, mainly in additive manufacturing and electronics. His previous roles include CEO of Maxify, VP Products at Stratasys, CEO at Xjet, EVP Products at Credence Systems, and President at Optonics.

The new management has undertaken a significant rethinking of the company, with Baharav stating: “We took a hard look at our product portfolio. Every offering must meet our vision of leadership in making industrial manufacturing solutions for advanced, complex parts.” He continued to say that the structure of the company had been streamlined, adding: “Less hierarchy, more execution, and a flatter, faster organisation better equipped to innovate and deliver.”

Thus the company will now focus on two core product groups: it’s own core additively manufactured electronics, and the surface mount pick and place technology that Nano Dimension acquired with Essemtec. In the meantime, a number of product groups have been discontinued, including Admatec, Formatec, Deep Cube and the Fabrica Group, which all came from earlier acquisitions. 

Baharav added: “These moves – along with broader organizational efficiencies – enabled us to reduce the annualized operating expenses of our core business by over $20 million and increase revenue per employee from $147,000 to 223,000, a 52 percent gain.”

Nano Dimension has also completed its two most recent acquisitions, Markforged and Desktop Metal. However, the presentation accompanying the financial results states that “Markforged has its share of operational cost issues that must be addressed,” which the company is doing. Assaf Zipori, who has been Chief Financial Officer of Markforged, was appointed as Nano Dimension’s new Chief Financial Officer on April 24, 2025 

In contrast, the presentation points out that Desktop Metal has liabilities and liquidity needs it cannot currently meet, for which Nano Dimension has had to provide funds to cover this shortfall. Desktop Metal is now evaluating its strategic alternatives but the reality is that this acquisition was driven by the previous management team so the new management is not committed to it.

Nano Dimension also included preliminary figures for the first quarter of 2025. This shows revenues of $14.4 million with $840 million in cash, bank deposits and so on up to 31 March 2025. 

The company is planning to host a strategic update in June 2025. In the meantime, you can find further details from nano-di.com.


Posted

in

, , ,

by

Syndicate content

You can license the articles from Printing and Manufacturing Journal to reproduce in other publications. I generally charge around £150 per article but I’m open to discussing this for each title, particularly for publishers that want to use multiple stories. I can provide high res versions of images for print publications.

I’m used to working with overseas publishers and am registered for VAT with the UK’s HMRC tax authority but obviously won’t charge VAT to companies outside the UK. You can find further details and a licensing form from this page, or just contact me directly here.

Support this site

If you find the stories here useful then please consider making a donation to help fund Printing and Manufacturing Journal, either as a one-off or a repeat payment. Journalism is only really useful if it’s truly independent and this is the only such news source serving the print/ manufacturing sectors.

However, there are costs involved in travelling to cover events, as well as maintaining this site, not to mention the time that it takes to carry out research, check facts and interview people. So if you value this work, then please help to maintain it and keep it free to read.

Subscribe

Never miss a story – subscribe to Printing and Manufacturing Journal to receive an email notification every time an article is published here. It’s completely free of charge and you can cancel the subscription at any point without any hassle. There’s no need to provide any information other than an email address and subscribers details are not for sale so there’s no risk of any further marketing spam.

Related stories

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *