Baldwin to launch TexCoat G4 fabric finishing

Baldwin Technology is planning to launch its TexCoat G4 application system for fabric finishing at next month’s ITMA show in Barcelona. This system helps various chemical finishes to be applied such as a water-repellant or fabric softeners.

Baldwin has developed this Texcoat 4 fabric finishing system.

TexCoat is a non-contact spray technology that allows chemicals to be evenly applied across the textile surface with no waste, while also reducing the water and energy consumption. Any excess chemical that’s over-sprayed can be recycled. It can be applied only where needed, either on one or both sides of the fabric. This gets around the problem that when water repellants are applied to laminated fabrics, the chemistry can affect the quality of the adhesion layer. Equally, as a non-contact approach it avoids the risk of the chemistry being diluted in wet-on-wet processes for a more consistent chemistry coverage. Also, since there’s no bath contamination during the finishing process, there’s no time wasted  during colour or fabric changeovers.

Since it only applies exactly the amount of chemistry that’s needed, it’s possible to achieve a wet pick-up level of 50 percent, which halves the water and energy consumption. According to Baldwin, the low wet pick-up levels together with a single side spray application allows for combined processes and can completely eliminate drying steps, for example, when working. with laminated fabrics and in finishing of upholstery textiles.

There are two main improvements over the existing third generation. Firstly, the system has been redesigned to achieve zero chemistry loss during job changeovers. Eric Norling, vice president of Baldwin’s Precision Application division, explains: “After each job the cleaning cycle starts and then the small amount of chemistry still in the system, in the pump, filter and so on, is automatically pumped out into a small holding container where the chemistry can be drained to be used for next production. After this the system is flushed with water to clean the system and make it ready for the next job. By doing this zero chemistry is wasted which is both good for the environment and for the profitability as the chemistry can be quite expensive.”

Secondly, this latest version has higher spray intensity to get deep impregnation of thick fabrics. Norling says: “We have a new pump in the G4 which allows for a higher and more even pressure, which is critical to provide deep impregnation of the fabrics, for example, when applying fabric softeners on thick fleece type of fabrics.”

Norling commented: “One of the biggest challenges facing the textile finishing industry is the environmental impact in terms of energy, chemical and water consumption, with continuously increasing environmental legislations and consumer demands to meet. Since the TexCoat G4 reduces both water and energy consumption and has zero chemistry waste in changeovers, a significantly more sustainable finishing process is achieved.” 

The TexCoat G4 is said to offer automated speed tracking, and real-time monitoring to track system uptime, performance, and chemistry usage, as well as active care alerts. It allows users to manage recipes, including automated chemistry and coverage selection, which should make for quick and easy changeovers. 

TexCoat G4 will work with a wide range of low-viscosity water-based chemicals, such as water-repellants, softeners and anti-microbials, both in wet-on-wet applications and lamination processes. It’s a completely sealed system, encapsulating all aerosols that makes for a healthy working environment for the operator.

Baldwin is currently investigating use of this system for applying the pre-treatment for digital print. Norling says: “This is a natural next step for us, but it is to be considered work in progress right now as it is a quite difficult process to secure.”

You can find more details on this at www.baldwintech.com.


Posted

in

,

by

Tags:

Syndicate content

You can license the articles from Printing and Manufacturing Journal to reproduce in other publications. I generally charge around £150 per article but I’m open to discussing this for each title, particularly for publishers that want to use multiple stories. I can provide high res versions of images for print publications.

I’m used to working with overseas publishers and am registered for VAT with the UK’s HMRC tax authority but obviously won’t charge VAT to companies outside the UK. You can find further details and a licensing form from this page, or just contact me directly here.

Support this site

If you find the stories here useful then please consider making a donation to help fund Printing and Manufacturing Journal, either as a one-off or a repeat payment. Journalism is only really useful if it’s truly independent and this is the only such news source serving the print/ manufacturing sectors.

However, there are costs involved in travelling to cover events, as well as maintaining this site, not to mention the time that it takes to carry out research, check facts and interview people. So if you value this work, then please help to maintain it and keep it free to read.

Subscribe

Never miss a story – subscribe to Printing and Manufacturing Journal to receive an email notification every time an article is published here. It’s completely free of charge and you can cancel the subscription at any point without any hassle. There’s no need to provide any information other than an email address and subscribers details are not for sale so there’s no risk of any further marketing spam.

Related stories

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *